Arduino Soil Moisture Sensor Relay Control

Arduino Soil Moisture Sensor Relay Control

CIRCUIT DIAGRAM :

MATERIALS :

Arduino
Soil Moisture Sensor
Relay Module 

CODE :

//Eliyas Science Info
//Soil Moisture Relay Sensor 

int Relay = 13; 
int sensor = 8; 
int val; 
void setup() {
  pinMode(13,OUTPUT); //Set pin 13 as OUTPUT pin, to send signal to relay
  pinMode(8,INPUT); //Set pin 8 as input pin, to receive data from Soil moisture sensor.
}

void loop() { 
  val = digitalRead(8); 
  if(val == LOW) 
  {
  digitalWrite(13,LOW); //if soil moisture sensor provides LOW value send LOW value to relay
  }
  else
  {
  digitalWrite(13,HIGH); //if soil moisture sensor provides HIGH value send HIGH value to relay
  }
  delay(400) ;
}

ELIYAS SCIENCE INFO ©

Comments

Post a Comment

Popular posts from this blog

Arduino MPU6050 Digital Spirit Level Measuring Device

Image
Arduino MPU6050 Digital Spirit Level Measuring Device CIRCUIT DIAGRAM : MATERIALS : Arduino NANO MPU6050 OLED Display Buzzer LED Breadboard CODE : //Eliyas Science Info //MPU6050 LEVEL Device Pitch Roll #include <Wire.h> #include <Adafruit_SSD1306.h> //OLED==================================================================== #define SCREEN_WIDTH 128 #define SCREEN_HEIGHT 64 #define OLED_RESET 4 Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET); //Level LEDs============================================================== int levelLED_neg2 = 5;   int levelLED_neg1 = 7; int levelLED_level = 8;  int levelLED_pos1 = 9;   int levelLED_pos2 = 11;  int buzzer = 13; //Variables for Gyroscope================================================= int gyro_x, gyro_y, gyro_z; long gyro_x_cal, gyro_y_cal, gyro_z_cal; boolean set_gyro_angles; long acc_x, acc_y, acc_z, acc_total_vector; float angle_roll_acc, angle_...
Read more

Arduino Timer Control Relay Devices

Image
Arduino Timer Control Relay Devices CIRCUIT DIAGRAM :  MATERIALS : Arduino Nano/UNO LiquidCrystal I2c Display Relay Module Buzzer Push Buttons BreadBoard Bulb Holder Socket Wires CODE : //Eliyas Science Info //Arduino Timer Relay - Triger relay for specific time #include <LiquidCrystal_I2C.h> //https://github.com/fdebrabander/Arduino-LiquidCrystal-I2C-library LiquidCrystal_I2C lcd(0x3F, 16, 2); // LCD HEX address 0x3F -- change according to yours #include "Countimer.h" //https://github.com/inflop/Countimer Countimer tdown; #include <EEPROM.h> #define bt_set A3 #define bt_up A2 #define bt_down A1 #define bt_start A0 int time_s = 0; int time_m = 0; int time_h = 0; int set = 0; int flag1=0, flag2=0; int relay = 5; int buzzer = 6; void setup() { Serial.begin (9600); pinMode(bt_set, INPUT_PULLUP); pinMode(bt_up, INPUT_PULLUP); pinMode(bt_down, INPUT_PULLUP); pinMode(bt_start, INPUT_PULLUP); pinMode(relay, OUTPUT); pinMode(buzze...
Read more

Arduino Secret Knock Pattern Door Lock

Image
Arduino Secret Knock Pattern Door Lock CIRCUIT DIAGRAM : MATERIALS : Arduino UNO / NANO Relay module 5V Solenoid Lock Speaker LED Resistor 220, 10k, 1M Push Button Wires Breadboard CODE : //Eliyas Science Info //Secret Knock Pattern Door Lock const int knockSensor = 0; const int programSwitch = 2; const int lockMotor = 3; const int redLED = 4; const int greenLED = 5;   const int threshold = 3; const int rejectValue = 25; const int averageRejectValue = 15; const int knockFadeTime = 150; const int lockTurnTime = 2000; const int maximumKnocks = 20; const int knockComplete = 1200; int secretCode[maximumKnocks] = {50, 25, 25, 50, 100, 50, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}; int knockReadings[maximumKnocks]; int knockSensorValue = 0; int programButtonPressed = false; void setup() {   pinMode(lockMotor, OUTPUT);   pinMode(redLED, OUTPUT);   pinMode(greenLED, OUTPUT);   pinMode(programSwitch, INPUT);      Serial.begin(9600);...
Read more