Arduino Visitors Counter | Automatic Light

ARDUINO VISITORS COUNTER | AUTOMATIC LIGHT

CIRCUIT DIAGRAM :

MATERIALS :

Arduino UNO 
IR Sensors 
Relay Module 
Potentiometer or resistor 
Breadboard 
Jumpers 

CODE :

//Visitors Counter and Automatic Room Light
//Eliyas Science Info

#include<LiquidCrystal.h>
LiquidCrystal lcd(13,12,11,10,9,8);

#define in 14
#define out 19
#define relay 2

int count=0;

void IN()
{
    count++;
    lcd.clear();
    lcd.print("Person In Room:");
    lcd.setCursor(0,1);
    lcd.print(count);
    delay(1000);
}

void OUT()
{
  count--;
    lcd.clear();
    lcd.print("Person In Room:");
    lcd.setCursor(0,1);
    lcd.print(count);
    delay(1000);
}

void setup()
{
  lcd.begin(16,2);
  lcd.print("Visitor Counter");
  delay(2000);
  pinMode(in, INPUT);
  pinMode(out, INPUT);
  pinMode(relay, OUTPUT);
  lcd.clear();
  lcd.print("Person In Room:");
  lcd.setCursor(0,1);
  lcd.print(count);
}

void loop()
{  
  
  if(digitalRead(in))
  IN();
  if(digitalRead(out))
  OUT();
  
  if(count<=0)
  {
    lcd.clear();
    digitalWrite(relay, LOW);
    lcd.clear();
    lcd.print("Nobody In Room");
    lcd.setCursor(0,1);
    lcd.print("Light Is Off");
    delay(200);
  }
  
  else
    digitalWrite(relay, HIGH);
  
}

ELIYAS SCIENCE INFO ©

Comments

Post a Comment

Popular posts from this blog

Arduino MPU6050 Digital Spirit Level Measuring Device

Image
Arduino MPU6050 Digital Spirit Level Measuring Device CIRCUIT DIAGRAM : MATERIALS : Arduino NANO MPU6050 OLED Display Buzzer LED Breadboard CODE : //Eliyas Science Info //MPU6050 LEVEL Device Pitch Roll #include <Wire.h> #include <Adafruit_SSD1306.h> //OLED==================================================================== #define SCREEN_WIDTH 128 #define SCREEN_HEIGHT 64 #define OLED_RESET 4 Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET); //Level LEDs============================================================== int levelLED_neg2 = 5;   int levelLED_neg1 = 7; int levelLED_level = 8;  int levelLED_pos1 = 9;   int levelLED_pos2 = 11;  int buzzer = 13; //Variables for Gyroscope================================================= int gyro_x, gyro_y, gyro_z; long gyro_x_cal, gyro_y_cal, gyro_z_cal; boolean set_gyro_angles; long acc_x, acc_y, acc_z, acc_total_vector; float angle_roll_acc, angle_...
Read more

Arduino Timer Control Relay Devices

Image
Arduino Timer Control Relay Devices CIRCUIT DIAGRAM :  MATERIALS : Arduino Nano/UNO LiquidCrystal I2c Display Relay Module Buzzer Push Buttons BreadBoard Bulb Holder Socket Wires CODE : //Eliyas Science Info //Arduino Timer Relay - Triger relay for specific time #include <LiquidCrystal_I2C.h> //https://github.com/fdebrabander/Arduino-LiquidCrystal-I2C-library LiquidCrystal_I2C lcd(0x3F, 16, 2); // LCD HEX address 0x3F -- change according to yours #include "Countimer.h" //https://github.com/inflop/Countimer Countimer tdown; #include <EEPROM.h> #define bt_set A3 #define bt_up A2 #define bt_down A1 #define bt_start A0 int time_s = 0; int time_m = 0; int time_h = 0; int set = 0; int flag1=0, flag2=0; int relay = 5; int buzzer = 6; void setup() { Serial.begin (9600); pinMode(bt_set, INPUT_PULLUP); pinMode(bt_up, INPUT_PULLUP); pinMode(bt_down, INPUT_PULLUP); pinMode(bt_start, INPUT_PULLUP); pinMode(relay, OUTPUT); pinMode(buzze...
Read more

Arduino Secret Knock Pattern Door Lock

Image
Arduino Secret Knock Pattern Door Lock CIRCUIT DIAGRAM : MATERIALS : Arduino UNO / NANO Relay module 5V Solenoid Lock Speaker LED Resistor 220, 10k, 1M Push Button Wires Breadboard CODE : //Eliyas Science Info //Secret Knock Pattern Door Lock const int knockSensor = 0; const int programSwitch = 2; const int lockMotor = 3; const int redLED = 4; const int greenLED = 5;   const int threshold = 3; const int rejectValue = 25; const int averageRejectValue = 15; const int knockFadeTime = 150; const int lockTurnTime = 2000; const int maximumKnocks = 20; const int knockComplete = 1200; int secretCode[maximumKnocks] = {50, 25, 25, 50, 100, 50, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}; int knockReadings[maximumKnocks]; int knockSensorValue = 0; int programButtonPressed = false; void setup() {   pinMode(lockMotor, OUTPUT);   pinMode(redLED, OUTPUT);   pinMode(greenLED, OUTPUT);   pinMode(programSwitch, INPUT);      Serial.begin(9600);...
Read more